1. Litter-Robot 4: Red light bar with partial white flashing (Globe position)
If your unit displays a red light bar with partial white flashing, this indicates that the unit did not detect the globe position during its previous cycle.
Visit for solutions if your Litter-Robot 4 has a red light bar with a partial white flashing globe. Get instant support and fixes today.
2. Litter-Robot 3: All three lights flashing (Globe position fault)
Check and clear any obstructions in the waste port. Waste clumps or toys could obstruct the globe rotation and cause a globe position or over-torque fault.
Find solutions for your Litter-Robot 3's three lights flashing position sensors issue. Fix issues with your Connect Upgrade Kit today!
3. Litter Robot III - Home positioning fault - RobotShop Community
22 apr 2024 · Recently our Litter Robot III LR3C-1200-CE (SN LR3CI359573) shows a home position fault. The globe stops at the end of the cycle just before ...
Recently our Litter Robot III LR3C-1200-CE (SN LR3CI359573) shows a home position fault. The globe stops at the end of the cycle just before it returns to its home position. Suggestions I found on the web didn’t help. It is using the official adapter and it is directly plugged in the wall socket. Up till now I just turn off the robot, reposition the globe by hand and turn it on again. It will cycle and will work for a while as expected until it doesn’t. Rinse and repeat. I don’t think the motor ...
4. Litter Robot 3 Home Position Fault - RobotShop Community
10 feb 2021 · The Hall Effect Sensor is the sensor responsible for the tracking of the globe's position. It's what makes your Litter-Robot so intelligent.
Hi! We got a Litter Robot 3 about 6 months ago. Yesterday it showed a Home Position Fault (all lights blinking sequentially from red to blue). I can’t seem to find anything online that deals with this precise issue. Would anyone have any suggestion? Thank you so much in advance for your help!
5. Litter-Robot 3: Fixing the globe magnets
Troubleshooting your disassembled Litter-Robot 3 Globe? Our guide helps you check magnet positions and correct errors for a smoothly functioning unit.
6. Litter Robot III - Flashing lights sequentially or flashing all at once
If the lights on the control panel blink, right to left, left to right or together, the problem is still the same: the robot has failed to track the position of ...
Most of you are here because there are 3 flashing lights on your Litter-Robot's control panel. Sometimes this problem is caused by a faulty power supply or the motor itself. If even after checking the set screw on the motor and checking the voltage on the power supply with a multimeter, the lights…
7. Litter Robot 4 Reinstalling the Globe Liner Weight
Open the bonnet: Press and hold the latches on both sides of the bonnet, then lift and rotate the bonnet to its open position. · Remove the globe: Using the ...
Discover how to reinstall the globe liner weight on your Litter-Robot 4. Get expert help and support. Click now to solve your issue fast!
8. [PDF] 15882-litter-robot-4-en.pdf
The Litter-Robot is ready for use when the Globe is at the Home position and the Light Bar on the Control Panel is blue. 1. When a cat enters the Globe, the Cat ...
9. https://raw.githubusercontent.com/dcmeglio/hubitat...
... Litter-Robot", namespace: "natekspencer", author: "Nathan Spencer ... Fault - Weight in the Litter-Robot is too heavy case "SCF": // Cat Sensor Fault ...
/** * Litter-Robot * * Copyright 2020 Nathan Spencer * * Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except * in compliance with the License. You may obtain a copy of the License at: * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software distributed under the License is distributed * on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License * for the specific language governing permissions and limitations under the License. * * * Known commands that can be called: * C - start cleaning cycle: unitStatus changes from RDY to CCP; upon completion, cycleCount += 1 and unitStatus briefly goes to CCC and panelLockActive = 1 then typically returns to unitStatus of RDY and panelLockActive of previous state * D - reset settings to defaults: sleepModeActive = 0, panelLockActive = 0, nightLightActive = 1, cleanCycleWaitTimeMinutes = 7 * L0 - panel lock off: panelLockActive = 0 * L1 - panel lock active: panelLockActive = 1 * N0 - night light off: nightLightActive = 0 * N1 - night light on: nightLightActive = 1 * P0 - turn power off: unitStatus changes = OFF; on the next report from the unit, powerStatus changes to NC and cleanCycleWaitTimeMinutes shows as 7; device is still wifi connected, but won't respond to any commands except P1 (power on), sleepModeActive and panelLockActive reset...
10. Litter-Robot III Open Air Troubleshooting - Cat Evolution
1 jan 2017 · The unit should perform an initialization cycle: the Globe will rotate counterclockwise to the Dump position, then rotate clockwise past the ...
If you have been troubleshooting issues with your Automatic Litter-Robot III Open Air to no avail, try this Fresh Restart to eliminate confounding conditions and identify the problem if there is one.
11. Litter robot cannot find sales home position
Litter robot cannot find sales home position, Litter Robot III Open Air Magnets Domestic Robots RobotShop sales. ... Troubleshooting Litter Robot 3 Globe Magnets ...
Technology Division - Premier Real Estate Photography | Virtual Tours | Aerial Photography. Sarasota, Bradenton, Anna Maria Island, Longboat Key, Lakewood Ranch, Siesta Key, Palmetto, Parrish...
12. Litter robot 3 pinch contact and dfi kit.
Checking For A Pinch Detect Fault Litter-Robot. Most likely worthwhile ... (Globe position fault) guide to inspect the position sensor. alaska mountain ...
404
13. litter-robot LR4 Bezel Seal Strips Pack Installation Guide - Manuals.plus
7 sep 2023 · Replace the globe by holding it by the handle and sliding it back into the base. Ensure the back of the globe is sitting flush in the rear ...
Ensure a tight seal and prevent leakage with the LR4 Bezel Seal Strips Pack. Follow our step-by-step instructions to install the lower globe seal strips for the Litter-Robot 4 waste disposal unit. Keep your unit functioning at its best.
14. Litter-Robot 3 Support, Troubleshooting, and Solutions
Litter-Robot 3: All three lights flashing (Globe position fault) · Litter-Robot 3: Blue light flashing (Drawer full indicator "DFI") · Litter-Robot 3: Buttons ...
Have questions about your Litter-Robot 3? Get quick solutions from our dedicated support page. Start troubleshooting now.
